Prozone Engineers

Features

Core • 16 MHz advanced STM8 core with Harvard architecture and 3-stage pipeline • Extended instruction set Memories • Program memory: 8 Kbyte Flash memory; data retention 20 years at 55 °C after 100 cycles • RAM: 1 Kbyte • Data memory: 128 bytes true data EEPROM; endurance up to 100 k write/erase cycles Clock, reset and supply management • 2.95 V to 5.5 V operating voltage • Flexible clock control, 4 master clock sources – Low-power crystal resonator oscillator – External clock input – Internal, user-trimmable 16 MHz RC – Internal low-power 128 kHz RC • Clock security system with clock monitor • Power management – Low-power modes (wait, active-halt, halt) – Switch-off peripheral clocks individually – Permanently active, low-consumption power-on and power-down reset Interrupt management • Nested interrupt controller with 32 interrupts • Up to 27 external interrupts on 6 vectors Timers • Advanced control timer: 16-bit, 4 CAPCOM channels, 3 complementary outputs, dead-time insertion and flexible synchronization • 16-bit general purpose timer, with 3 CAPCOM channels (IC, OC or PWM) • 8-bit basic timer with 8-bit prescaler • Auto wakeup timer • Window and independent watchdog timers Communications interfaces • UART with clock output for synchronous operation, SmartCard, IrDA, LIN master mode • SPI interface up to 8 Mbit/s • I 2C interface up to 400 Kbit/s Analog to digital converter (ADC) • 10-bit ADC, ± 1 LSB ADC with up to 5 multiplexed channels, scan mode and analog watchdog I/Os • Up to 28 I/Os on a 32-pin package including 21 high-sink outputs • Highly robust I/O d

Features Core– Max fCPU: up to 24 MHz, 0 wait states @fCPU 16 MHz– Advanced STM8 core with Harvardarchitecture and 3-stage pipeline– Extended instruction set– Max 20 MIPS @ 24 MHz Memories– Program: up to 128 Kbytes Flash; dataretention 20 years at 55 °C after 10 kcycles– Data: up to 2 Kbytes true data EEPROM;endurance 300 kcycles– RAM: up to 6 Kbytes Clock, reset and supply management– 2.95 to 5.5 V operating voltage– Low power crystal resonator oscillator– External clock input– Internal, user-trimmable 16 MHz RC– Internal low power 128 kHz RC– Clock security system with clock monitor– Wait, active-halt, & halt low power modes– Peripheral clocks switched off individually– Permanently active, low consumptionpower-on and power-down reset Interrupt management– Nested interrupt controller with 32interrupts– Up to 37 external interrupts on 6 vectors Timers– 2x 16-bit general purpose timers, with 2+3CAPCOM channels (IC, OC or PWM)– Advanced control timer: 16-bit, 4 CAPCOMchannels, 3 complementary outputs, deadtime insertion and flexible synchronization– 8-bit basic timer with 8-bit prescaler– Auto wakeup timer– Window watchdog, independent watchdog Communications interfaces– High speed 1 Mbit/s active beCAN 2.0B– UART with clock output for synchronousoperation - LIN master mode– UART with LIN 2.1 compliant, master/slavemodes and automatic resynchronization– SPI interface up to 10 Mbit/s– I2C interface up to 400 Kbit/s 10-bit ADC with up to 16 channels I/Os– Up to 68 I/Os on an 80-pin packageincluding 18 high sink outputs– Highly robust I/O design, immune againstcurrent injection– Development support– Single wire interface module (SWIM) anddebug module (DM) 96-bit unique ID key for each device

Features Core– Max fCPU: up to 24 MHz, 0 wait states @fCPU 16 MHz– Advanced STM8 core with Harvardarchitecture and 3-stage pipeline– Extended instruction set– Max 20 MIPS @ 24 MHz Memories– Program: up to 128 Kbytes Flash; dataretention 20 years at 55 °C after 10 kcycles– Data: up to 2 Kbytes true data EEPROM;endurance 300 kcycles– RAM: up to 6 Kbytes Clock, reset and supply management– 2.95 to 5.5 V operating voltage– Low power crystal resonator oscillator– External clock input– Internal, user-trimmable 16 MHz RC– Internal low power 128 kHz RC– Clock security system with clock monitor– Wait, active-halt, & halt low power modes– Peripheral clocks switched off individually– Permanently active, low consumptionpower-on and power-down reset Interrupt management– Nested interrupt controller with 32interrupts– Up to 37 external interrupts on 6 vectors Timers– 2x 16-bit general purpose timers, with 2+3CAPCOM channels (IC, OC or PWM)– Advanced control timer: 16-bit, 4 CAPCOMchannels, 3 complementary outputs, deadtime insertion and flexible synchronization– 8-bit basic timer with 8-bit prescaler– Auto wakeup timer– Window watchdog, independent watchdog Communications interfaces– High speed 1 Mbit/s active beCAN 2.0B– UART with clock output for synchronousoperation - LIN master mode– UART with LIN 2.1 compliant, master/slavemodes and automatic resynchronization– SPI interface up to 10 Mbit/s– I2C interface up to 400 Kbit/s 10-bit ADC with up to 16 channels I/Os– Up to 68 I/Os on an 80-pin packageincluding 18 high sink outputs– Highly robust I/O design, immune againstcurrent injection– Development support– Single wire interface module (SWIM) anddebug module (DM) 96-bit unique ID key for each device

Features • ARM® 32-bit Cortex®-M3 CPU Core – 72 MHz maximum frequency, 1.25 DMIPS/MHz (Dhrystone 2.1) performance at 0 wait state memory access – Single-cycle multiplication and hardware division • Memories – 64 or 128 Kbytes of Flash memory – 20 Kbytes of SRAM • Clock, reset and supply management – 2.0 to 3.6 V application supply and I/Os – POR, PDR, and programmable voltage detector (PVD) – 4-to-16 MHz crystal oscillator – Internal 8 MHz factory-trimmed RC – Internal 40 kHz RC – PLL for CPU clock – 32 kHz oscillator for RTC with calibration • Low-power – Sleep, Stop and Standby modes – VBAT supply for RTC and backup registers • 2 x 12-bit, 1 µs A/D converters (up to 16 channels) – Conversion range: 0 to 3.6 V – Dual-sample and hold capability – Temperature sensor • DMA – 7-channel DMA controller – Peripherals supported: timers, ADC, SPIs, I 2Cs and USARTs • Up to 80 fast I/O ports – 26/37/51/80 I/Os, all mappable on 16 external interrupt vectors and almost all 5 V-tolerant

STM32U575xx Series Controllers
Ultra-low-power Arm® Cortex®-M33 32-bit MCU+TrustZone®+FPU, 240 DMIPS, up to 2 MB Flash memory, 786 KB SRAM, SMPS


Ultra-low-power with FlexPowerControl• 1.71 V to 3.6 V power supply• –40 °C to +85/125 °C temperature range• Low-power background autonomous mode(LPBAM): autonomous peripherals with DMA,functional down to Stop 2 mode• VBAT mode: supply for RTC, 32 x 32-bit backupregisters and 2-Kbyte backup SRAM• 160 nA Shutdown mode (24 wakeup pins)• 210 nA Standby mode (24 wakeup pins)• 440 nA Standby mode with RTC• 1.9 μA Stop 3 mode with 16-Kbyte SRAM• 4.3 µA Stop 3 mode with full SRAM• 4.0 µA Stop 2 mode with 16-Kbyte SRAM• 8.95 µA Stop 2 mode with full SRAM• 19.5 μA/MHz Run mode @ 3.3 V

Core• Arm® 32-bit Cortex®-M33 CPU withTrustZone®, MPU, DSP, and FPU

STM8S103F2

16 MHz STM8S 8-bit MCU, up to 8 Kbytes Flash, data EEPROM,10-bit ADC, 3 timers, UART, SPI, I²C

FeaturesCore• 16 MHz advanced STM8 core with Harvardarchitecture and 3-stage pipeline• Extended instruction setMemories• Program memory: 8 Kbyte Flash; dataretention 20 years at 55 °C after 10 kcycle• Data memory: 640 byte true data EEPROM;endurance 300 kcycle• RAM: 1 KbyteClock, reset and supply management• 2.95 to 5.5 V operating voltage• Flexible clock control, 4 master clock sources– Low power crystal resonator oscillator– External clock input– Internal, user-trimmable 16 MHz RC– Internal low-power 128 kHz RC• Clock security system with clock monitor• Power management:– Low-power modes (wait, active-halt, halt)– Switch-off peripheral clocks individually• Permanently active, low-consumption poweron and power-down resetInterrupt management• Nested interrupt controller with 32 interrupts• Up to 27 external interrupts on 6 vectorsTimers• Advanced control timer: 16-bit, 4 CAPCOMchannels, 3 complementary outputs, dead-timeinsertion and flexible synchronization• 16-bit general purpose timer, with 3 CAPCOMchannels (IC, OC or PWM)• 8-bit basic timer with 8-bit prescaler• Auto wake-up timer• Window watchdog and independent watchdogtimersCommunication interfaces• UART with clock output for synchronousoperation, SmartCard, IrDA, LIN master mode• SPI interface up to 8 Mbit/s• I2C interface up to 400 kbit/sAnalog to digital converter (ADC)• 10-bit, ±1 LSB ADC with up to 5 multiplexedchannels, scan mode and analog watchdogI/Os• Up to 28 I/Os on a 32-pin package including21 high sink outputs• Highly robust I/O design, immune againstcurrent injectionUnique ID• 96-bit unique key for each device

Manufacturer: STMicroelectronics Product Category: 8-bit Microcontrollers - MCU RoHS: Details Series: STM8S001J3 Mounting Style: SMD/SMT Package/Case: SOIC-8 Core: STM8 Program Memory Size: 8 kB Data Bus Width: 8 bit ADC Resolution: 10 bit Maximum Clock Frequency: 16 MHz Number of I/Os: 5 I/O Data RAM Size: 1 kB Supply Voltage - Min: 2.95 V Supply Voltage - Max: 5.5 V Minimum Operating Temperature: - 40 C Maximum Operating Temperature: + 125 C Packaging: Reel Packaging: Cut Tape Packaging: MouseReel Brand: STMicroelectronics Product Type: 8-bit Microcontrollers - MCU 2500 Subcategory: Microcontrollers - MCU Unit Weight: 80 mg

Features core– max fcpu: up to 24 mhz, 0 wait states @fcpu 16 mhz– advanced stm8 core with harvardarchitecture and 3-stage pipeline– extended instruction set– max 20 mips @ 24 mhz memories– program: up to 128 kbytes flash; dataretention 20 years at 55 °c after 10 kcycles– data: up to 2 kbytes true data eeprom;endurance 300 kcycles– ram: up to 6 kbytes clock, reset and supply management– 2.95 to 5.5 v operating voltage– low power crystal resonator oscillator– external clock input– internal, user-trimmable 16 mhz rc– internal low power 128 khz rc– clock security system with clock monitor– wait, active-halt, & halt low power modes– peripheral clocks switched off individually– permanently active, low consumptionpower-on and power-down reset interrupt management– nested interrupt controller with 32interrupts– up to 37 external interrupts on 6 vectors timers– 2x 16-bit general purpose timers, with 2+3capcom channels (ic, oc or pwm)– advanced control timer: 16-bit, 4 capcomchannels, 3 complementary outputs, deadtime insertion and flexible synchronization– 8-bit basic timer with 8-bit prescaler– auto wakeup timer– window watchdog, independent watchdog communications interfaces– high speed 1 mbit/s active becan 2.0b– uart with clock output for synchronousoperation - lin master mode– uart with lin 2.1 compliant, master/slavemodes and automatic resynchronization– spi interface up to 10 mbit/s– i2c interface up to 400 kbit/s 10-bit adc with up to 16 channels I/os– up to 68 I/os on an 80-pin packageincluding 18 high sink outputs– highly robust I/o design, immune againstcurrent injection– development support– single wire interface module (swim) anddebug module (dm) 96-bit unique id key for each device

Features Core– Max fCPU: up to 24 MHz, 0 wait states @fCPU 16 MHz– Advanced STM8 core with Harvardarchitecture and 3-stage pipeline– Extended instruction set– Max 20 MIPS @ 24 MHz Memories– Program: up to 128 Kbytes Flash; dataretention 20 years at 55 °C after 10 kcycles– Data: up to 2 Kbytes true data EEPROM;endurance 300 kcycles– RAM: up to 6 Kbytes Clock, reset and supply management– 2.95 to 5.5 V operating voltage– Low power crystal resonator oscillator– External clock input– Internal, user-trimmable 16 MHz RC– Internal low power 128 kHz RC– Clock security system with clock monitor– Wait, active-halt, & halt low power modes– Peripheral clocks switched off individually– Permanently active, low consumptionpower-on and power-down reset Interrupt management– Nested interrupt controller with 32interrupts– Up to 37 external interrupts on 6 vectors Timers– 2x 16-bit general purpose timers, with 2+3CAPCOM channels (IC, OC or PWM)– Advanced control timer: 16-bit, 4 CAPCOMchannels, 3 complementary outputs, deadtime insertion and flexible synchronization– 8-bit basic timer with 8-bit prescaler– Auto wakeup timer– Window watchdog, independent watchdog Communications interfaces– High speed 1 Mbit/s active beCAN 2.0B– UART with clock output for synchronousoperation - LIN master mode– UART with LIN 2.1 compliant, master/slavemodes and automatic resynchronization– SPI interface up to 10 Mbit/s– I2C interface up to 400 Kbit/s 10-bit ADC with up to 16 channels I/Os– Up to 68 I/Os on an 80-pin packageincluding 18 high sink outputs– Highly robust I/O design, immune againstcurrent injection– Development support– Single wire interface module (SWIM) anddebug module (DM) 96-bit unique ID key for each deviceADM2483BRWZ Integrated Circuit , ADSP-BF532SBBZ400 , ADSP-BF535PBB-200 , BQ76925PWR IC BAT MFUNC LI-ION 3-6C 20TSSOP , BQ7693000DBT Battery Management IC 30TSSOP , BQ7694003DBTR IC BATT MON MULTI 9-15C 44TSSOP , BQ7791501PWR Texas Instruments , CS4398-CZZ CIRRUS LOGIC , DAC5662IPFB , DS2438AZ+T&R IC BATT MONITOR SMART 8SOIC , DS2438Z+ IC BATT MONITOR SMART 8SOIC , DS2438Z+T&R IC BATT MONITOR SMART 8SOIC , Espressif ESP32-S3-WROOM-1 Wifi Module , Hip4082ipz Smd IC , L9805E STM Motor Driver IC , PIC 16F15244 T-I/REB , QW3862 3862 DIP-8 Power Management Chip IC , STM 32C031 C6T6 , STM32C031C6U6 ST Controller , STM32F030K6T6TR STMicroelectronics Microcontroller , STM32F072CBT6, ST Microcontroller , STM32F411RET6TR STM Microcontroller IC MCU 32BIT 512KB FLASH 64LQFP , STM32G0B1CCU6 STM Microcontroller IC MCU 32BIT 256KB FLSH 48UFQFPN , STM32G0B1CEU6 STM Microcontroller IC MCU 32BIT 512KB FLSH 48UFQFPN , STM32L071CZT6TR IC MCU 32BIT 192KB FLASH 48LQFP , STM32L071KBU6 IC MCU 32BIT 128KB FLSH 32UFQFPN , STM32L151CCU6TR IC MCU 32BIT 256KB FLSH 48UFQFPN , STM32L431CCU6TR STM Microelectronics , STM32L433VCT6TR STM Controller IC MCU 32BIT 256KB FLASH 100LQFP , STM8L151G6U6 STM Controller IC MCU 8BIT 32KB FLASH 28UFQFPN , STM8S003F3P6 IC MCU 8BIT 8KB FLASH 20TSSOP , Stm8S003K3P6 St Microcontroller , Stm8S003K3 Stm Controller , TLP250H Toshiba Semiconductor and Storage , TMS320BC52PJ80 Digital Signal Processor , TMS320C32PCM50 , W9864G6KH-5 Winbond Ic , W9864G6KH-6 Winbond IC , WM8778SEDS/V

Features Core– Max fCPU: up to 24 MHz, 0 wait states @fCPU 16 MHz– Advanced STM8 core with Harvardarchitecture and 3-stage pipeline– Extended instruction set– Max 20 MIPS @ 24 MHz Memories– Program: up to 128 Kbytes Flash; dataretention 20 years at 55 °C after 10 kcycles– Data: up to 2 Kbytes true data EEPROM;endurance 300 kcycles– RAM: up to 6 Kbytes Clock, reset and supply management– 2.95 to 5.5 V operating voltage– Low power crystal resonator oscillator– External clock input– Internal, user-trimmable 16 MHz RC– Internal low power 128 kHz RC– Clock security system with clock monitor– Wait, active-halt, & halt low power modes– Peripheral clocks switched off individually– Permanently active, low consumptionpower-on and power-down reset Interrupt management– Nested interrupt controller with 32interrupts– Up to 37 external interrupts on 6 vectors Timers– 2x 16-bit general purpose timers, with 2+3CAPCOM channels (IC, OC or PWM)– Advanced control timer: 16-bit, 4 CAPCOMchannels, 3 complementary outputs, deadtime insertion and flexible synchronization– 8-bit basic timer with 8-bit prescaler– Auto wakeup timer– Window watchdog, independent watchdog Communications interfaces– High speed 1 Mbit/s active beCAN 2.0B– UART with clock output for synchronousoperation - LIN master mode– UART with LIN 2.1 compliant, master/slavemodes and automatic resynchronization– SPI interface up to 10 Mbit/s– I2C interface up to 400 Kbit/s 10-bit ADC with up to 16 channels I/Os– Up to 68 I/Os on an 80-pin packageincluding 18 high sink outputs– Highly robust I/O design, immune againstcurrent injection– Development support– Single wire interface module (SWIM) anddebug module (DM) 96-bit unique ID key for each deviceADM2483BRWZ Integrated Circuit , ADSP-BF532SBBZ400 , ADSP-BF535PBB-200 , BQ76925PWR IC BAT MFUNC LI-ION 3-6C 20TSSOP , BQ7693000DBT Battery Management IC 30TSSOP , BQ7694003DBTR IC BATT MON MULTI 9-15C 44TSSOP , BQ7791501PWR Texas Instruments , CS4398-CZZ CIRRUS LOGIC , DAC5662IPFB , DS2438AZ+T&R IC BATT MONITOR SMART 8SOIC , DS2438Z+ IC BATT MONITOR SMART 8SOIC , DS2438Z+T&R IC BATT MONITOR SMART 8SOIC , Espressif ESP32-S3-WROOM-1 Wifi Module , Hip4082ipz Smd IC , L9805E STM Motor Driver IC , PIC 16F15244 T-I/REB , QW3862 3862 DIP-8 Power Management Chip IC , STM 32C031 C6T6 , STM32C031C6U6 ST Controller , STM32F030K6T6TR STMicroelectronics Microcontroller , STM32F072CBT6, ST Microcontroller , STM32F411RET6TR STM Microcontroller IC MCU 32BIT 512KB FLASH 64LQFP , STM32G0B1CCU6 STM Microcontroller IC MCU 32BIT 256KB FLSH 48UFQFPN , STM32G0B1CEU6 STM Microcontroller IC MCU 32BIT 512KB FLSH 48UFQFPN , STM32L071CZT6TR IC MCU 32BIT 192KB FLASH 48LQFP , STM32L071KBU6 IC MCU 32BIT 128KB FLSH 32UFQFPN , STM32L151CCU6TR IC MCU 32BIT 256KB FLSH 48UFQFPN , STM32L431CCU6TR STM Microelectronics , STM32L433VCT6TR STM Controller IC MCU 32BIT 256KB FLASH 100LQFP , STM8L151G6U6 STM Controller IC MCU 8BIT 32KB FLASH 28UFQFPN , STM8S003F3P6 IC MCU 8BIT 8KB FLASH 20TSSOP , Stm8S003K3P6 St Microcontroller , Stm8S003K3 Stm Controller , TLP250H Toshiba Semiconductor and Storage , TMS320BC52PJ80 Digital Signal Processor , TMS320C32PCM50 , W9864G6KH-5 Winbond Ic , W9864G6KH-6 Winbond IC , WM8778SEDS/V

Features Core– Max fCPU: up to 24 MHz, 0 wait states @fCPU 16 MHz– Advanced STM8 core with Harvardarchitecture and 3-stage pipeline– Extended instruction set– Max 20 MIPS @ 24 MHz Memories– Program: up to 128 Kbytes Flash; dataretention 20 years at 55 °C after 10 kcycles– Data: up to 2 Kbytes true data EEPROM;endurance 300 kcycles– RAM: up to 6 Kbytes Clock, reset and supply management– 2.95 to 5.5 V operating voltage– Low power crystal resonator oscillator– External clock input– Internal, user-trimmable 16 MHz RC– Internal low power 128 kHz RC– Clock security system with clock monitor– Wait, active-halt, & halt low power modes– Peripheral clocks switched off individually– Permanently active, low consumptionpower-on and power-down reset Interrupt management– Nested interrupt controller with 32interrupts– Up to 37 external interrupts on 6 vectors Timers– 2x 16-bit general purpose timers, with 2+3CAPCOM channels (IC, OC or PWM)– Advanced control timer: 16-bit, 4 CAPCOMchannels, 3 complementary outputs, deadtime insertion and flexible synchronization– 8-bit basic timer with 8-bit prescaler– Auto wakeup timer– Window watchdog, independent watchdog Communications interfaces– High speed 1 Mbit/s active beCAN 2.0B– UART with clock output for synchronousoperation - LIN master mode– UART with LIN 2.1 compliant, master/slavemodes and automatic resynchronization– SPI interface up to 10 Mbit/s– I2C interface up to 400 Kbit/s 10-bit ADC with up to 16 channels I/Os– Up to 68 I/Os on an 80-pin packageincluding 18 high sink outputs– Highly robust I/O design, immune againstcurrent injection– Development support– Single wire interface module (SWIM) anddebug module (DM) 96-bit unique ID key for each device

Features Core– Max fCPU: up to 24 MHz, 0 wait states @fCPU 16 MHz– Advanced STM8 core with Harvardarchitecture and 3-stage pipeline– Extended instruction set– Max 20 MIPS @ 24 MHz Memories– Program: up to 128 Kbytes Flash; dataretention 20 years at 55 °C after 10 kcycles– Data: up to 2 Kbytes true data EEPROM;endurance 300 kcycles– RAM: up to 6 Kbytes Clock, reset and supply management– 2.95 to 5.5 V operating voltage– Low power crystal resonator oscillator– External clock input– Internal, user-trimmable 16 MHz RC– Internal low power 128 kHz RC– Clock security system with clock monitor– Wait, active-halt, & halt low power modes– Peripheral clocks switched off individually– Permanently active, low consumptionpower-on and power-down reset Interrupt management– Nested interrupt controller with 32interrupts– Up to 37 external interrupts on 6 vectors Timers– 2x 16-bit general purpose timers, with 2+3CAPCOM channels (IC, OC or PWM)– Advanced control timer: 16-bit, 4 CAPCOMchannels, 3 complementary outputs, deadtime insertion and flexible synchronization– 8-bit basic timer with 8-bit prescaler– Auto wakeup timer– Window watchdog, independent watchdog Communications interfaces– High speed 1 Mbit/s active beCAN 2.0B– UART with clock output for synchronousoperation - LIN master mode– UART with LIN 2.1 compliant, master/slavemodes and automatic resynchronization– SPI interface up to 10 Mbit/s– I2C interface up to 400 Kbit/s 10-bit ADC with up to 16 channels I/Os– Up to 68 I/Os on an 80-pin packageincluding 18 high sink outputs– Highly robust I/O design, immune againstcurrent injection– Development support– Single wire interface module (SWIM) anddebug module (DM) 96-bit unique ID key for each device

Features Core– Max fCPU: up to 24 MHz, 0 wait states @fCPU 16 MHz– Advanced STM8 core with Harvardarchitecture and 3-stage pipeline– Extended instruction set– Max 20 MIPS @ 24 MHz Memories– Program: up to 128 Kbytes Flash; dataretention 20 years at 55 °C after 10 kcycles– Data: up to 2 Kbytes true data EEPROM;endurance 300 kcycles– RAM: up to 6 Kbytes Clock, reset and supply management– 2.95 to 5.5 V operating voltage– Low power crystal resonator oscillator– External clock input– Internal, user-trimmable 16 MHz RC– Internal low power 128 kHz RC– Clock security system with clock monitor– Wait, active-halt, & halt low power modes– Peripheral clocks switched off individually– Permanently active, low consumptionpower-on and power-down reset Interrupt management– Nested interrupt controller with 32interrupts– Up to 37 external interrupts on 6 vectors Timers– 2x 16-bit general purpose timers, with 2+3CAPCOM channels (IC, OC or PWM)– Advanced control timer: 16-bit, 4 CAPCOMchannels, 3 complementary outputs, deadtime insertion and flexible synchronization– 8-bit basic timer with 8-bit prescaler– Auto wakeup timer– Window watchdog, independent watchdog Communications interfaces– High speed 1 Mbit/s active beCAN 2.0B– UART with clock output for synchronousoperation - LIN master mode– UART with LIN 2.1 compliant, master/slavemodes and automatic resynchronization– SPI interface up to 10 Mbit/s– I2C interface up to 400 Kbit/s 10-bit ADC with up to 16 channels I/Os– Up to 68 I/Os on an 80-pin packageincluding 18 high sink outputs– Highly robust I/O design, immune againstcurrent injection– Development support– Single wire interface module (SWIM) anddebug module (DM) 96-bit unique ID key for each device

Features Core– Max fCPU: up to 24 MHz, 0 wait states @fCPU 16 MHz– Advanced STM8 core with Harvardarchitecture and 3-stage pipeline– Extended instruction set– Max 20 MIPS @ 24 MHz Memories– Program: up to 128 Kbytes Flash; dataretention 20 years at 55 °C after 10 kcycles– Data: up to 2 Kbytes true data EEPROM;endurance 300 kcycles– RAM: up to 6 Kbytes Clock, reset and supply management– 2.95 to 5.5 V operating voltage– Low power crystal resonator oscillator– External clock input– Internal, user-trimmable 16 MHz RC– Internal low power 128 kHz RC– Clock security system with clock monitor– Wait, active-halt, & halt low power modes– Peripheral clocks switched off individually– Permanently active, low consumptionpower-on and power-down reset Interrupt management– Nested interrupt controller with 32interrupts– Up to 37 external interrupts on 6 vectors Timers– 2x 16-bit general purpose timers, with 2+3CAPCOM channels (IC, OC or PWM)– Advanced control timer: 16-bit, 4 CAPCOMchannels, 3 complementary outputs, deadtime insertion and flexible synchronization– 8-bit basic timer with 8-bit prescaler– Auto wakeup timer– Window watchdog, independent watchdog Communications interfaces– High speed 1 Mbit/s active beCAN 2.0B– UART with clock output for synchronousoperation - LIN master mode– UART with LIN 2.1 compliant, master/slavemodes and automatic resynchronization– SPI interface up to 10 Mbit/s– I2C interface up to 400 Kbit/s 10-bit ADC with up to 16 channels I/Os– Up to 68 I/Os on an 80-pin packageincluding 18 high sink outputs– Highly robust I/O design, immune againstcurrent injection– Development support– Single wire interface module (SWIM) anddebug module (DM) 96-bit unique ID key for each device

Features• Core: Arm® 32-bit Cortex®-M0+ CPU,frequency up to 64 MHz• -40°C to 85°C/105°C/125°C operatingtemperature• Memories– Up to 512 Kbytes of Flash memory withprotection and securable area, two banks,read-while-write support– 144 Kbytes of SRAM (128 Kbytes with HWparity check)• CRC calculation unit• Reset and power management– Voltage range: 1.7 V to 3.6 V– Separate I/O supply pin (1.6 V to 3.6 V)– Power-on/Power-down reset (POR/PDR)– Programmable Brownout reset (BOR)– Programmable voltage detector (PVD)– Low-power modes:Sleep, Stop, Standby, Shutdown– VBAT supply for RTC and backup registers

STM32U585xx
Ultra-low-power Arm® Cortex®-M33 32-bit MCU+TrustZone®+FPU,240 DMIPS, up to 2 MB Flash memory, 786 KB SRAM, SMPS


Features

Ultra-low-power with FlexPowerControl • 1.71 V to 3.6 V power supply • –40 °C to +85/125 °C temperature range • Low-power background autonomous mode (LPBAM): autonomous peripherals with DMA, functional down to Stop 2 mode • VBAT mode: supply for RTC, 32 x 32-bit backup registers and 2-Kbyte backup SRAM • 160 nA Shutdown mode (24 wakeup pins) • 210 nA Standby mode (24 wakeup pins) • 440 nA Standby mode with RTC • 1.9 μA Stop 3 mode with 16-Kbyte SRAM • 4.3 µA Stop 3 mode with full SRAM • 4.0 µA Stop 2 mode with 16-Kbyte SRAM • 8.95 µA Stop 2 mode with full SRAM • 19.5 μA/MHz Run mode @ 3.3 V Core • Arm® 32-bit Cortex®-M33 CPU with TrustZone®, MPU, DSP, and FPU

Features Core– Max fCPU: up to 24 MHz, 0 wait states @fCPU 16 MHz– Advanced STM8 core with Harvardarchitecture and 3-stage pipeline– Extended instruction set– Max 20 MIPS @ 24 MHz Memories– Program: up to 128 Kbytes Flash; dataretention 20 years at 55 °C after 10 kcycles– Data: up to 2 Kbytes true data EEPROM;endurance 300 kcycles– RAM: up to 6 Kbytes Clock, reset and supply management– 2.95 to 5.5 V operating voltage– Low power crystal resonator oscillator– External clock input– Internal, user-trimmable 16 MHz RC– Internal low power 128 kHz RC– Clock security system with clock monitor– Wait, active-halt, & halt low power modes– Peripheral clocks switched off individually– Permanently active, low consumptionpower-on and power-down reset Interrupt management– Nested interrupt controller with 32interrupts– Up to 37 external interrupts on 6 vectors Timers– 2x 16-bit general purpose timers, with 2+3CAPCOM channels (IC, OC or PWM)– Advanced control timer: 16-bit, 4 CAPCOMchannels, 3 complementary outputs, deadtime insertion and flexible synchronization– 8-bit basic timer with 8-bit prescaler– Auto wakeup timer– Window watchdog, independent watchdog Communications interfaces– High speed 1 Mbit/s active beCAN 2.0B– UART with clock output for synchronousoperation - LIN master mode– UART with LIN 2.1 compliant, master/slavemodes and automatic resynchronization– SPI interface up to 10 Mbit/s– I2C interface up to 400 Kbit/s 10-bit ADC with up to 16 channels I/Os– Up to 68 I/Os on an 80-pin packageincluding 18 high sink outputs– Highly robust I/O design, immune againstcurrent injection– Development support– Single wire interface module (SWIM) anddebug module (DM) 96-bit unique ID key for each device

Features  High performance, low power AVR® 8-bit microcontroller  Advanced RISC architecture  131 powerful instructions – most single clock cycle execution  32  8 general purpose working registers  Fully static operation  Up to 16MIPS throughput at 16MHz   On-chip 2-cycle multiplier  High endurance non-volatile memory segments  32K bytes of in-system self-programmable flash program memory  1Kbytes EEPROM  2Kbytes internal SRAM  Write/erase cycles: 10,000 flash/100,000 EEPROM  Optional boot code section with independent lock bits  In-system programming by on-chip boot program  True read-while-write operation   Programming lock for software security  Peripheral features  Two 8-bit Timer/Counters with separate prescaler and compare mode  One 16-bit Timer/Counter with separate prescaler, compare mode, and capture mode  Real time counter with separate oscillator   Six PWM channels  8-channel 10-bit ADC in TQFP and QFN/MLF package  Temperature measurement   Programmable serial USART  Master/slave SPI serial interface  Byte-oriented 2-wire serial interface (Phillips I2 C compatible)  Programmable watchdog timer with separate on-chip oscillator  On-chip analog comparator  Interrupt and wake-up on pin change  Special microcontroller features  Power-on reset and programmable brown-out detection  Internal calibrated oscillator  External and internal interrupt sources  Six sleep modes: Idle, ADC noise reduction, power-save, power-down, standby, and extended standby

The high-performance, low-power Microchip 8-bit AVR® RISC-based microcontroller combines 256 KB ISP flash memory, 8 KB SRAM, 4 KB EEPROM, 86 general purpose I/O lines, 32 general purpose working registers, real-time counter, six flexible timer/counters with compare modes, PWM, four USARTs, byte-oriented Two-Wire serial interface, 16-channel 10-bit A/D converter, and a JTAG interface for on-chip debugging. The device achieves a throughput of 16 MIPS at 16 MHz and operates between 4.5-5.5 volts.

By executing powerful instructions in a single clock cycle, the device achieves a throughput approaching one MIPS per MHz, balancing power consumption and processing speed.

FeaturesCore 16 MHz advanced STM8 core with Harvardarchitecture and 3-stage pipeline Extended instruction setMemories Program memory: up to 32 Kbyte Flash; dataretention 20 years at 55 °C after 10 kcycle Data memory: up to 1 Kbyte true dataEEPROM; endurance 300 kcycle RAM: up to 2 KbyteClock, reset and supply management 2.95 to 5.5 V operating voltage Flexible clock control, 4 master clock sources– Low power crystal resonator oscillator– External clock input– Internal, user-trimmable 16 MHz RC– Internal low-power 128 kHz RC Clock security system with clock monitor Power management:– Low-power modes (wait, active-halt, halt)– Switch-off peripheral clocks individually Permanently active, low-consumption poweron and power-down resetInterrupt management Nested interrupt controller with 32 interrupts Up to 37 external interrupts on 6 vectorsTimers Advanced control timer: 16-bit, 4 CAPCOMchannels, 3 complementary outputs, dead-timeinsertion and flexible synchronization 2x16-bit general purpose timer, with 2+3CAPCOM channels (IC, OC or PWM) 8-bit basic timer with 8-bit prescaler Auto wake-up timer Window watchdog and independent watchdogtimersCommunication interfaces UART with clock output for synchronousoperation, SmartCard, IrDA, LIN master mode SPI interface up to 8 Mbit/s I2C interface up to 400 kbit/sAnalog to digital converter (ADC) 10-bit, ±1 LSB ADC with up to 10 multiplexedchannels, scan mode and analog watchdogI/Os Up to 38 I/Os on a 48-pin package including16 high sink outputs Highly robust I/O design, immune againstcurrent injectionUnique ID 96-bit unique key for each device

FeaturesCore 16 MHz advanced STM8 core with Harvardarchitecture and 3-stage pipeline Extended instruction setMemories Program memory: up to 32 Kbyte Flash; dataretention 20 years at 55 °C after 10 kcycle Data memory: up to 1 Kbyte true dataEEPROM; endurance 300 kcycle RAM: up to 2 KbyteClock, reset and supply management 2.95 to 5.5 V operating voltage Flexible clock control, 4 master clock sources– Low power crystal resonator oscillator– External clock input– Internal, user-trimmable 16 MHz RC– Internal low-power 128 kHz RC Clock security system with clock monitor Power management:– Low-power modes (wait, active-halt, halt)– Switch-off peripheral clocks individually Permanently active, low-consumption poweron and power-down resetInterrupt management Nested interrupt controller with 32 interrupts Up to 37 external interrupts on 6 vectorsTimers Advanced control timer: 16-bit, 4 CAPCOMchannels, 3 complementary outputs, dead-timeinsertion and flexible synchronization 2x16-bit general purpose timer, with 2+3CAPCOM channels (IC, OC or PWM) 8-bit basic timer with 8-bit prescaler Auto wake-up timer Window watchdog and independent watchdogtimersCommunication interfaces UART with clock output for synchronousoperation, SmartCard, IrDA, LIN master mode SPI interface up to 8 Mbit/s I2C interface up to 400 kbit/sAnalog to digital converter (ADC) 10-bit, ±1 LSB ADC with up to 10 multiplexedchannels, scan mode and analog watchdogI/Os Up to 38 I/Os on a 48-pin package including16 high sink outputs Highly robust I/O design, immune againstcurrent injectionUnique ID 96-bit unique key for each device

ST’s STM32F205/215 microcontrollers are designed for medical, industrial and consumer applications where the high level of integration and performance, embedded memories and peripherals inside packages as small as 4 x 4 mm are required.
Performance: At 120 MHz, the STM32F205/215 products deliver 150 DMIPS/398 CoreMark performance executing from Flash memory, with 0-wait states using ST’s ART Accelerator.
Power efficiency: ST’s 90 nm process, ART Accelerator and the dynamic power scaling enables the current consumption in run mode and executing from Flash memory to be as low as 175 µA/MHz at 120 MHz.
Rich connectivity: Superior and innovative peripherals
2x USB OTG (one with HS support)Audio: dedicated audio PLL and 2 half duplex I²SUp to 15 communication interfaces (including 6 USARTs running at up to 7.5 Mbit/s, 3x SPI running at up to 30 Mbit/s,3x I²C, 2x CAN, SDIO)Analog: two 12-bit DACs, three 12-bit ADCs reaching 2 MSPS or 6 MSPS in interleaved modeUp to 17 timers: 16- and 32-bit timersEasily extendable memory range using the flexible static memory controller supporting Compact Flash, SRAM, PSRAM, NOR and NAND memoriesAnalog true random number generatorThe STM32F215 also integrates a crypto/hash processor providing hardware acceleration for AES 128, 192, 256,Triple DES, and hash (MD5, SHA-1)The STM32F205/215 devices cover from 128 Kbytes to 1 MByte of Flash, up to 128 Kbytes of SRAM and from 64 to 144 pins in packages as small as 4 x 4 mm.

Available in Delhi at Prozone EngineersADM2483BRWZ Integrated Circuit , ADSP-BF532SBBZ400 , ADSP-BF535PBB-200 , BQ76925PWR IC BAT MFUNC LI-ION 3-6C 20TSSOP , BQ7693000DBT Battery Management IC 30TSSOP , BQ7694003DBTR IC BATT MON MULTI 9-15C 44TSSOP , BQ7791501PWR Texas Instruments , CS4398-CZZ CIRRUS LOGIC , DAC5662IPFB , DS2438AZ+T&R IC BATT MONITOR SMART 8SOIC , DS2438Z+ IC BATT MONITOR SMART 8SOIC , DS2438Z+T&R IC BATT MONITOR SMART 8SOIC , Espressif ESP32-S3-WROOM-1 Wifi Module , Hip4082ipz Smd IC , L9805E STM Motor Driver IC , PIC 16F15244 T-I/REB , QW3862 3862 DIP-8 Power Management Chip IC , STM 32C031 C6T6 , STM32C031C6U6 ST Controller , STM32F030K6T6TR STMicroelectronics Microcontroller , STM32F072CBT6, ST Microcontroller , STM32F411RET6TR STM Microcontroller IC MCU 32BIT 512KB FLASH 64LQFP , STM32G0B1CCU6 STM Microcontroller IC MCU 32BIT 256KB FLSH 48UFQFPN , STM32G0B1CEU6 STM Microcontroller IC MCU 32BIT 512KB FLSH 48UFQFPN , STM32L071CZT6TR IC MCU 32BIT 192KB FLASH 48LQFP , STM32L071KBU6 IC MCU 32BIT 128KB FLSH 32UFQFPN , STM32L151CCU6TR IC MCU 32BIT 256KB FLSH 48UFQFPN , STM32L431CCU6TR STM Microelectronics , STM32L433VCT6TR STM Controller IC MCU 32BIT 256KB FLASH 100LQFP , STM8L151G6U6 STM Controller IC MCU 8BIT 32KB FLASH 28UFQFPN , STM8S003F3P6 IC MCU 8BIT 8KB FLASH 20TSSOP , Stm8S003K3P6 St Microcontroller , Stm8S003K3 Stm Controller , TLP250H Toshiba Semiconductor and Storage , TMS320BC52PJ80 Digital Signal Processor , TMS320C32PCM50 , W9864G6KH-5 Winbond Ic , W9864G6KH-6 Winbond IC , WM8778SEDS/V

Manufacturer: STMicroelectronics Product Category: 8-bit Microcontrollers - MCU RoHS: Details Series: STM8S005C6 Mounting Style: SMD/SMT Package/Case: LQFP-48 Core: STM8 Program Memory Size: 32 kB Data Bus Width: 8 bit ADC Resolution: 10 bit Maximum Clock Frequency: 16 MHz Number of I/Os: 38 I/O Data RAM Size: 2 kB Supply Voltage - Min: 2.95 V Supply Voltage - Max: 5.5 V Minimum Operating Temperature: - 40 C Maximum Operating Temperature: + 85 C Packaging: Tray Brand: STMicroelectronics Data ROM Size: 128 B Data ROM Type: EEPROM Interface Type: I2C, SPI, UART Moisture Sensitive: Yes Number of ADC Channels: 10 Channel Number of Timers/Counters: 3 Timer Processor Series: STM8S005 Product Type: 8-bit Microcontrollers - MCU Program Memory Type: Flash 1500 Subcategory: Microcontrollers - MCU Unit Weight: 181.700 mg

FeaturesCore 16 MHz advanced STM8 core with Harvardarchitecture and 3-stage pipeline Extended instruction setMemories Program memory: up to 32 Kbyte Flash; dataretention 20 years at 55 °C after 10 kcycle Data memory: up to 1 Kbyte true dataEEPROM; endurance 300 kcycle RAM: up to 2 KbyteClock, reset and supply management 2.95 to 5.5 V operating voltage Flexible clock control, 4 master clock sources– Low power crystal resonator oscillator– External clock input– Internal, user-trimmable 16 MHz RC– Internal low-power 128 kHz RC Clock security system with clock monitor Power management:– Low-power modes (wait, active-halt, halt)– Switch-off peripheral clocks individually Permanently active, low-consumption poweron and power-down resetInterrupt management Nested interrupt controller with 32 interrupts Up to 37 external interrupts on 6 vectorsTimers Advanced control timer: 16-bit, 4 CAPCOMchannels, 3 complementary outputs, dead-timeinsertion and flexible synchronization 2x16-bit general purpose timer, with 2+3CAPCOM channels (IC, OC or PWM) 8-bit basic timer with 8-bit prescaler Auto wake-up timer Window watchdog and independent watchdogtimersCommunication interfaces UART with clock output for synchronousoperation, SmartCard, IrDA, LIN master mode SPI interface up to 8 Mbit/s I2C interface up to 400 kbit/sAnalog to digital converter (ADC) 10-bit, ±1 LSB ADC with up to 10 multiplexedchannels, scan mode and analog watchdogI/Os Up to 38 I/Os on a 48-pin package including16 high sink outputs Highly robust I/O design, immune againstcurrent injectionUnique ID 96-bit unique key for each device

STM8S103F2/STM8S103F3


Features Core• 16 MHz advanced STM8 core with Harvardarchitecture and 3-stage pipeline• Extended instruction setMemories• Program memory: 8 Kbyte Flash; dataretention 20 years at 55 °C after 10 kcycle• Data memory: 640 byte true data EEPROM;endurance 300 kcycle• RAM: 1 KbyteClock, reset and supply management• 2.95 to 5.5 V operating voltage• Flexible clock control, 4 master clock sources– Low power crystal resonator oscillator– External clock input– Internal, user-trimmable 16 MHz RC– Internal low-power 128 kHz RC• Clock security system with clock monitor• Power management:– Low-power modes (wait, active-halt, halt)– Switch-off peripheral clocks individually• Permanently active, low-consumption poweronand power-down resetInterrupt management• Nested interrupt controller with 32 interrupts• Up to 27 external interrupts on 6 vectorsTimers• Advanced control timer: 16-bit, 4 CAPCOMchannels, 3 complementary outputs, dead-timeinsertion and flexible synchronization• 16-bit general purpose timer, with 3 CAPCOMchannels (IC, OC or PWM)• 8-bit basic timer with 8-bit prescaler• Auto wake-up timer• Window watchdog and independent watchdogtimersCommunication interfaces• UART with clock output for synchronousoperation, SmartCard, IrDA, LIN master mode• SPI interface up to 8 Mbit/s• I2C interface up to 400 kbit/sAnalog to digital converter (ADC)• 10-bit, ±1 LSB ADC with up to 5 multiplexedchannels, scan mode and analog watchdogI/Os• Up to 28 I/Os on a 32-pin package including21 high sink outputs• Highly robust I/O design, immune againstcurrent injectionUnique ID• 96-bit unique key for each device

FeaturesCore 16 MHz advanced STM8 core with Harvardarchitecture and 3-stage pipeline Extended instruction setMemories Program memory: up to 32 Kbyte Flash; dataretention 20 years at 55 °C after 10 kcycle Data memory: up to 1 Kbyte true dataEEPROM; endurance 300 kcycle RAM: up to 2 KbyteClock, reset and supply management 2.95 to 5.5 V operating voltage Flexible clock control, 4 master clock sources– Low power crystal resonator oscillator– External clock input– Internal, user-trimmable 16 MHz RC– Internal low-power 128 kHz RC Clock security system with clock monitor Power management:– Low-power modes (wait, active-halt, halt)– Switch-off peripheral clocks individually Permanently active, low-consumption poweron and power-down resetInterrupt management Nested interrupt controller with 32 interrupts Up to 37 external interrupts on 6 vectorsTimers Advanced control timer: 16-bit, 4 CAPCOMchannels, 3 complementary outputs, dead-timeinsertion and flexible synchronization 2x16-bit general purpose timer, with 2+3CAPCOM channels (IC, OC or PWM) 8-bit basic timer with 8-bit prescaler Auto wake-up timer Window watchdog and independent watchdogtimersCommunication interfaces UART with clock output for synchronousoperation, SmartCard, IrDA, LIN master mode SPI interface up to 8 Mbit/s I2C interface up to 400 kbit/sAnalog to digital converter (ADC) 10-bit, ±1 LSB ADC with up to 10 multiplexedchannels, scan mode and analog watchdogI/Os Up to 38 I/Os on a 48-pin package including16 high sink outputs Highly robust I/O design, immune againstcurrent injectionUnique ID 96-bit unique key for each device

FeaturesCore 16 MHz advanced STM8 core with Harvardarchitecture and 3-stage pipeline Extended instruction setMemories Program memory: up to 32 Kbyte Flash; dataretention 20 years at 55 °C after 10 kcycle Data memory: up to 1 Kbyte true dataEEPROM; endurance 300 kcycle RAM: up to 2 KbyteClock, reset and supply management 2.95 to 5.5 V operating voltage Flexible clock control, 4 master clock sources– Low power crystal resonator oscillator– External clock input– Internal, user-trimmable 16 MHz RC– Internal low-power 128 kHz RC Clock security system with clock monitor Power management:– Low-power modes (wait, active-halt, halt)– Switch-off peripheral clocks individually Permanently active, low-consumption poweron and power-down resetInterrupt management Nested interrupt controller with 32 interrupts Up to 37 external interrupts on 6 vectorsTimers Advanced control timer: 16-bit, 4 CAPCOMchannels, 3 complementary outputs, dead-timeinsertion and flexible synchronization 2x16-bit general purpose timer, with 2+3CAPCOM channels (IC, OC or PWM) 8-bit basic timer with 8-bit prescaler Auto wake-up timer Window watchdog and independent watchdogtimersCommunication interfaces UART with clock output for synchronousoperation, SmartCard, IrDA, LIN master mode SPI interface up to 8 Mbit/s I2C interface up to 400 kbit/sAnalog to digital converter (ADC) 10-bit, ±1 LSB ADC with up to 10 multiplexedchannels, scan mode and analog watchdogI/Os Up to 38 I/Os on a 48-pin package including16 high sink outputs Highly robust I/O design, immune againstcurrent injectionUnique ID 96-bit unique key for each device

FeaturesCore 16 MHz advanced STM8 core with Harvardarchitecture and 3-stage pipeline Extended instruction setMemories Program memory: up to 32 Kbyte Flash; dataretention 20 years at 55 °C after 10 kcycle Data memory: up to 1 Kbyte true dataEEPROM; endurance 300 kcycle RAM: up to 2 KbyteClock, reset and supply management 2.95 to 5.5 V operating voltage Flexible clock control, 4 master clock sources– Low power crystal resonator oscillator– External clock input– Internal, user-trimmable 16 MHz RC– Internal low-power 128 kHz RC Clock security system with clock monitor Power management:– Low-power modes (wait, active-halt, halt)– Switch-off peripheral clocks individually Permanently active, low-consumption poweron and power-down resetInterrupt management Nested interrupt controller with 32 interrupts Up to 37 external interrupts on 6 vectorsTimers Advanced control timer: 16-bit, 4 CAPCOMchannels, 3 complementary outputs, dead-timeinsertion and flexible synchronization 2x16-bit general purpose timer, with 2+3CAPCOM channels (IC, OC or PWM) 8-bit basic timer with 8-bit prescaler Auto wake-up timer Window watchdog and independent watchdogtimersCommunication interfaces UART with clock output for synchronousoperation, SmartCard, IrDA, LIN master mode SPI interface up to 8 Mbit/s I2C interface up to 400 kbit/sAnalog to digital converter (ADC) 10-bit, ±1 LSB ADC with up to 10 multiplexedchannels, scan mode and analog watchdogI/Os Up to 38 I/Os on a 48-pin package including16 high sink outputs Highly robust I/O design, immune againstcurrent injectionUnique ID 96-bit unique key for each device

FeaturesCore 16 MHz advanced STM8 core with Harvardarchitecture and 3-stage pipeline Extended instruction setMemories Program memory: up to 32 Kbyte Flash; dataretention 20 years at 55 °C after 10 kcycle Data memory: up to 1 Kbyte true dataEEPROM; endurance 300 kcycle RAM: up to 2 KbyteClock, reset and supply management 2.95 to 5.5 V operating voltage Flexible clock control, 4 master clock sources– Low power crystal resonator oscillator– External clock input– Internal, user-trimmable 16 MHz RC– Internal low-power 128 kHz RC Clock security system with clock monitor Power management:– Low-power modes (wait, active-halt, halt)– Switch-off peripheral clocks individually Permanently active, low-consumption poweron and power-down resetInterrupt management Nested interrupt controller with 32 interrupts Up to 37 external interrupts on 6 vectorsTimers Advanced control timer: 16-bit, 4 CAPCOMchannels, 3 complementary outputs, dead-timeinsertion and flexible synchronization 2x16-bit general purpose timer, with 2+3CAPCOM channels (IC, OC or PWM) 8-bit basic timer with 8-bit prescaler Auto wake-up timer Window watchdog and independent watchdogtimersCommunication interfaces UART with clock output for synchronousoperation, SmartCard, IrDA, LIN master mode SPI interface up to 8 Mbit/s I2C interface up to 400 kbit/sAnalog to digital converter (ADC) 10-bit, ±1 LSB ADC with up to 10 multiplexedchannels, scan mode and analog watchdogI/Os Up to 38 I/Os on a 48-pin package including16 high sink outputs Highly robust I/O design, immune againstcurrent injectionUnique ID 96-bit unique key for each device

Features Core– Max fCPU: up to 24 MHz, 0 wait states @fCPU 16 MHz– Advanced STM8 core with Harvardarchitecture and 3-stage pipeline– Extended instruction set– Max 20 MIPS @ 24 MHz Memories– Program: up to 128 Kbytes Flash; dataretention 20 years at 55 °C after 10 kcycles– Data: up to 2 Kbytes true data EEPROM;endurance 300 kcycles– RAM: up to 6 Kbytes Clock, reset and supply management– 2.95 to 5.5 V operating voltage– Low power crystal resonator oscillator– External clock input– Internal, user-trimmable 16 MHz RC– Internal low power 128 kHz RC– Clock security system with clock monitor– Wait, active-halt, & halt low power modes– Peripheral clocks switched off individually– Permanently active, low consumptionpower-on and power-down reset Interrupt management– Nested interrupt controller with 32interrupts– Up to 37 external interrupts on 6 vectors Timers– 2x 16-bit general purpose timers, with 2+3CAPCOM channels (IC, OC or PWM)– Advanced control timer: 16-bit, 4 CAPCOMchannels, 3 complementary outputs, deadtime insertion and flexible synchronization– 8-bit basic timer with 8-bit prescaler– Auto wakeup timer– Window watchdog, independent watchdog Communications interfaces– High speed 1 Mbit/s active beCAN 2.0B– UART with clock output for synchronousoperation - LIN master mode– UART with LIN 2.1 compliant, master/slavemodes and automatic resynchronization– SPI interface up to 10 Mbit/s– I2C interface up to 400 Kbit/s 10-bit ADC with up to 16 channels I/Os– Up to 68 I/Os on an 80-pin packageincluding 18 high sink outputs– Highly robust I/O design, immune againstcurrent injection– Development support– Single wire interface module (SWIM) anddebug module (DM) 96-bit unique ID key for each device

Manufacturer: STMicroelectronics Product Category: 8-bit Microcontrollers - MCU RoHS: Details Series: STM8S003F3 Mounting Style: SMD/SMT Package/Case: TSSOP-20 Core: STM8 Program Memory Size: 8 kB Data Bus Width: 8 bit ADC Resolution: 10 bit Maximum Clock Frequency: 16 MHz Number of I/Os: 16 I/O Data RAM Size: 1 kB Supply Voltage - Min: 2.95 V Supply Voltage - Max: 5.5 V Minimum Operating Temperature: - 40 C Maximum Operating Temperature: + 85 C Packaging: Tube Brand: STMicroelectronics Data RAM Type: RAM Data ROM Size: 128 B Data ROM Type: EEPROM Interface Type: I2C, SPI, UART Number of ADC Channels: 5 Channel Number of Timers/Counters: 3 Timer Processor Series: STM8S Product Type: 8-bit Microcontrollers - MCU Program Memory Type: Flash 1480 Subcategory: Microcontrollers - MCU Unit Weight: 200 mg

Features Core– Max fCPU: up to 24 MHz, 0 wait states @fCPU 16 MHz– Advanced STM8 core with Harvardarchitecture and 3-stage pipeline– Extended instruction set– Max 20 MIPS @ 24 MHz Memories– Program: up to 128 Kbytes Flash; dataretention 20 years at 55 °C after 10 kcycles– Data: up to 2 Kbytes true data EEPROM;endurance 300 kcycles– RAM: up to 6 Kbytes Clock, reset and supply management– 2.95 to 5.5 V operating voltage– Low power crystal resonator oscillator– External clock input– Internal, user-trimmable 16 MHz RC– Internal low power 128 kHz RC– Clock security system with clock monitor– Wait, active-halt, & halt low power modes– Peripheral clocks switched off individually– Permanently active, low consumptionpower-on and power-down reset Interrupt management– Nested interrupt controller with 32interrupts– Up to 37 external interrupts on 6 vectors Timers– 2x 16-bit general purpose timers, with 2+3CAPCOM channels (IC, OC or PWM)– Advanced control timer: 16-bit, 4 CAPCOMchannels, 3 complementary outputs, deadtime insertion and flexible synchronization– 8-bit basic timer with 8-bit prescaler– Auto wakeup timer– Window watchdog, independent watchdog Communications interfaces– High speed 1 Mbit/s active beCAN 2.0B– UART with clock output for synchronousoperation - LIN master mode– UART with LIN 2.1 compliant, master/slavemodes and automatic resynchronization– SPI interface up to 10 Mbit/s– I2C interface up to 400 Kbit/s 10-bit ADC with up to 16 channels I/Os– Up to 68 I/Os on an 80-pin packageincluding 18 high sink outputs– Highly robust I/O design, immune againstcurrent injection– Development support– Single wire interface module (SWIM) anddebug module (DM) 96-bit unique ID key for each device

FeaturesCore• Max fCPU: 16 MHz• Advanced STM8 core with Harvardarchitecture and 3-stage pipeline• Extended instruction setMemories• Medium-density Flash/EEPROM– Program memory: 32 Kbytes of Flashmemory; data retention 20 years at 55 °Cafter 100 cycles– Data memory: 128 bytes true dataEEPROM; endurance up to 100 kwrite/erase cycles• RAM: 2 KbytesClock, reset and supply management• 2.95 V to 5.5 operating voltage• Flexible clock control, 4 master clock sources– Low-power crystal resonator oscillator– External clock input– Internal, user-trimmable 16 MHz RC– Internal low-power 128 kHz RC• Clock security system with clock monitor• Power management– Low-power modes (wait, active-halt, halt)– Switch-off peripheral clocks individually– Permanently active, low-consumptionpower-on and power-down resetInterrupt management• Nested interrupt controller with 32 interrupts• Up to 37 external interrupts on 6 vectors

Features Core– Max fCPU: up to 24 MHz, 0 wait states @fCPU 16 MHz– Advanced STM8 core with Harvardarchitecture and 3-stage pipeline– Extended instruction set– Max 20 MIPS @ 24 MHz Memories– Program: up to 128 Kbytes Flash; dataretention 20 years at 55 °C after 10 kcycles– Data: up to 2 Kbytes true data EEPROM;endurance 300 kcycles– RAM: up to 6 Kbytes Clock, reset and supply management– 2.95 to 5.5 V operating voltage– Low power crystal resonator oscillator– External clock input– Internal, user-trimmable 16 MHz RC– Internal low power 128 kHz RC– Clock security system with clock monitor– Wait, active-halt, & halt low power modes– Peripheral clocks switched off individually– Permanently active, low consumptionpower-on and power-down reset Interrupt management– Nested interrupt controller with 32interrupts– Up to 37 external interrupts on 6 vectors Timers– 2x 16-bit general purpose timers, with 2+3CAPCOM channels (IC, OC or PWM)– Advanced control timer: 16-bit, 4 CAPCOMchannels, 3 complementary outputs, deadtime insertion and flexible synchronization– 8-bit basic timer with 8-bit prescaler– Auto wakeup timer– Window watchdog, independent watchdog Communications interfaces– High speed 1 Mbit/s active beCAN 2.0B– UART with clock output for synchronousoperation - LIN master mode– UART with LIN 2.1 compliant, master/slavemodes and automatic resynchronization– SPI interface up to 10 Mbit/s– I2C interface up to 400 Kbit/s 10-bit ADC with up to 16 channels I/Os– Up to 68 I/Os on an 80-pin packageincluding 18 high sink outputs– Highly robust I/O design, immune againstcurrent injection– Development support– Single wire interface module (SWIM) anddebug module (DM) 96-bit unique ID key for each device

Features Core– Max fCPU: up to 24 MHz, 0 wait states @fCPU 16 MHz– Advanced STM8 core with Harvardarchitecture and 3-stage pipeline– Extended instruction set– Max 20 MIPS @ 24 MHz Memories– Program: up to 128 Kbytes Flash; dataretention 20 years at 55 °C after 10 kcycles– Data: up to 2 Kbytes true data EEPROM;endurance 300 kcycles– RAM: up to 6 Kbytes Clock, reset and supply management– 2.95 to 5.5 V operating voltage– Low power crystal resonator oscillator– External clock input– Internal, user-trimmable 16 MHz RC– Internal low power 128 kHz RC– Clock security system with clock monitor– Wait, active-halt, & halt low power modes– Peripheral clocks switched off individually– Permanently active, low consumptionpower-on and power-down reset Interrupt management– Nested interrupt controller with 32interrupts– Up to 37 external interrupts on 6 vectors Timers– 2x 16-bit general purpose timers, with 2+3CAPCOM channels (IC, OC or PWM)– Advanced control timer: 16-bit, 4 CAPCOMchannels, 3 complementary outputs, deadtime insertion and flexible synchronization– 8-bit basic timer with 8-bit prescaler– Auto wakeup timer– Window watchdog, independent watchdog Communications interfaces– High speed 1 Mbit/s active beCAN 2.0B– UART with clock output for synchronousoperation - LIN master mode– UART with LIN 2.1 compliant, master/slavemodes and automatic resynchronization– SPI interface up to 10 Mbit/s– I2C interface up to 400 Kbit/s 10-bit ADC with up to 16 channels I/Os– Up to 68 I/Os on an 80-pin packageincluding 18 high sink outputs– Highly robust I/O design, immune againstcurrent injection– Development support– Single wire interface module (SWIM) anddebug module (DM) 96-bit unique ID key for each device